t qp369182 dc- 6 ghz gain block applications ? ? catv / satv / moca ? point to point ? defense & aerospace ? test & measurement equipment ? general purpose wireless sot - 89 package product featur es ? ? flat, broadband frequency response ? 20.7 db gain at 1.9 ghz ? 3.9 db noise figure at 1.9 ghz ? + 28 dbm output ip3 at 1.9 ghz ? +15.1 dbm p1db at 1.9 ghz ? 50 ohm cascadable gain block ? single supply, 45 ma current ? sot - 89 package functional block diagram rf in gnd rf out gnd 1 2 3 4 pin configuration pin no. label 1 rf in 3 rf out 2,4 gnd general description the tqp36918 2 is a general - purpose buffer amplifier that offers high dynamic range in a low - cost surface - mount package. at 1.9 ghz, the amplifier typica lly provides 20.7 db gain, +2 8 dbm oip3, and 3. 9 db noise figure while drawing 45 ma current. the device combines dependable performance with consistent quality to maintain mttf values exceeding 100 years at mounting temperatures of +85c. the device is h oused in a lead - free/green/rohs - compliant industry - standard sot - 89 package. the tqp36918 2 consists of a darlington - pair amplifier using triquint?s high reliability in gap/gaas hbt process technology. only dc- blocking capacitors, a bias resistor, and an in ductive rf choke are required for operation. th is broadband mmic amplifier can be directly applied to various current and next generation wireless technologies such as cdma, w - cdma, and lte. in addition, the tqp36918 2 will work for other applications w ithin the dc to 6 ghz frequency range . ordering information part no. description tqp369182 ingap/gaas hbt gain block tqp369182 - pcb 500?6000 m - 1 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
t qp369182 dc- 6 ghz gain block recommended operating conditions parameter min typ max units t case ? absolute maximum ratings parameter rating storage temperature ? rf input power, cw, 50, t=25 electrical specifications test conditions unless otherwise noted: i cc = 45 ma , t case = +25c, 50 system parameter conditions min typ max units operational frequency ra nge dc 6 000 mhz test frequency 1900 mhz gain 19.2 20.7 22.2 db input return loss - 21 db output return loss - 20 db output p1db +15.1 dbm output ip3 pout=0 dbm/tone, f= 1 mhz - 2 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
t qp369182 dc- 6 ghz gain block s - parameters test co nditions: v c c =+3.9 v (typ.), i cc =45 ma (typ.), t case =+25 c, 50 system, calibrated to device leads freq ( m hz) s11 (db) s11 (ang) s21 (db) s21 (ang) s12 (db) s12 (ang) s22 (db) s22 (ang) 10 - 23.9 - 178.7 22.8 179.6 - 24.4 1.2 - 28.1 153.9 20 - 23.4 - 178.6 22 .8 179.1 - 24.4 0.7 - 29.1 163.4 50 - 23.2 176.2 22.8 178.2 - 24.3 0.1 - 29.4 173.6 100 - 23.1 169.2 22.8 175.3 - 24.3 - 0.3 - 28.9 169.4 200 - 23.5 160.3 22.8 170.8 - 24.2 - 1.7 - 29.7 159.7 500 - 23.2 122.4 22.6 157.9 - 24.3 - 4.9 - 29.7 159.4 900 - 22.1 99.0 22.2 14 1.0 - 24.3 - 9.2 - 29.5 149.7 1000 - 21.3 90.5 22.2 136.9 - 24.3 - 10.4 - 28.0 152.1 1500 - 20.6 65.3 21.7 116.5 - 24.2 - 16.1 - 25.1 146.4 1900 - 19.0 44.7 21.3 101.2 - 24.2 - 20.8 - 22.7 144.5 2000 - 18.3 42.5 21.2 97.7 - 24.2 - 21.7 - 22.8 147.2 2500 - 18.3 29.6 20.6 79.1 - 24.2 - 26.5 - 20.0 123.9 3000 - 18.3 7.2 20.0 62.1 - 24.2 - 32.2 - 17.6 119.9 3500 - 17.4 - 12.4 19.4 45.4 - 24.2 - 38.2 - 17.1 116.3 4000 - 19.8 - 23.5 18.9 28.7 - 24.0 - 44.0 - 15.6 102.9 4500 - 20.8 - 40.6 18.4 12.3 - 24.2 - 49.5 - 14.7 97.0 5000 - 24.1 - 85.7 17.9 - 3.3 - 24.4 - 55.5 - 14.7 91.8 5500 - 20.8 - 124.5 17.6 - 19.7 - 24.4 - 61.0 - 13.6 88.7 6000 - 23.0 - 163.2 17.2 - 35.3 - 24.7 - 64.9 - 12.7 92.1 datasheet: rev f 8 / 1 8 /1 4 - 3 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
t qp369182 dc- 6 ghz gain block tq p369182 - pcb evaluation board (500?6000 mhz) c2 c1 l1 c3 j4 j3 j1 j2 q1 r1 ? c3 56 pf c2 56 pf c1 0.018 uf vcc notes: 1. see evaluation board pcb information section for material and stack -up. 2. all components are of 0603 size unless otherwise stated. bill of material ? tqp369182 - pcb reference des. value description manuf. part number q1 n/ a high linearity lna gain block triquint tqp369182 c1 0.018 uf cap, chip, 0603, 16v, x7r, 10% various c2, c3 56 pf cap, chip, 0603, 50v, npo, 5% various l1 39 nh inductor, 0603, 5%, cs series coilcraft r1
res, chip, 0805, 1/10w, 5% various c omponent values for specific frequencies frequency (mhz) 50 500 900 1900 2200 2500 3500 l1 820 nh 220 nh 68 nh 27 nh 22 nh 18 nh 15 nh c2, c3 .018 uf 1000 pf 100 pf 68 pf 68 pf 56 pf 39 pf bias resistor values for various supply voltages v supply (v) 5 6 7 8 9 10 12 r1 24
47
68
91
110
130
180
component size 0805 1206 1210 1210 1210 2010 2010 datasheet: rev f 8 / 1 8 /1 4 - 4 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
t qp369182 dc- 6 ghz gain block typical performance ? tqp369182 - pcb test conditions unless otherwise noted: v supply =+5 v, r 1 = 24 , i cc = 45 ma, t case = +25 c parameter typical value units fr equency 500 900 1900 2100 2600 3500 4000 5000 6000 mhz gain 22.3 22.0 20.7 20.6 20.5 19.4 18.9 17.9 17.2 db input return loss - 16 - 24.4 - 21.0 - 21.1 - 15.5 - 17.4 - 19.8 - 24.1 - 23 db output return loss - 16 - 28 - 20 - 23.1 - 20.4 - 17.1 - 15.6 - 14.7 - 12.7 db out put p1db +16.3 +16.1 +15.1 +15.0 +14.8 +14.6 +13.7 +12.7 +11 dbm oip3 +29.6 +29.6 +28.0 +27.9 +26.8 +26.3 +25.5 +23.4 +22.5 dbm noise f igure 3.8 3.8 3.9 4.0 4.0 4.3 4.3 3.9 4.1 db notes: 1. oip3 measured with two tones at an output power of 0 dbm / tone s eparated by 1 mhz. performance plots ? tqp36918 2 - pcb test conditions unless otherwise noted: v supply =+5 v, r 1 = 24 , i cc = 45 ma, t case = +25 c 14 16 18 20 22 24 0 1000 2000 3000 4000 5000 6000 |s21| (db) frequency (mhz) gain vs. frequency +85 c +25 c 40 c - 40 - 30 - 20 - 10 0 0 1000 2000 3000 4000 5000 6000 |s11| (db) frequency (mhz) input return loss vs. frequency +85 c +25 c ?40 ?40 datasheet: rev f 8 / 1 8 /1 4 - 5 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
t qp369182 dc- 6 ghz gain block pin configuration and description rf in gnd rf out gnd 1 2 3 4 pin no. label description 1 rf in rf i nput, matched to 50 ohms. external dc block is required. 3 rf out rf o utput / dc supply , matched to 50 ohms . external dc block , bias choke, and dropping resistor is required. 2, 4, backside paddle gnd paddle rf/dc ground. use recommended via pattern to min imize inductance and thermal resistance. see pcb mounting pattern for suggested footprint. evaluation board pcb information triquint pcb 10 75825 material and stack - up 50 ohm line dimensions: width=0.0 28" spa cing=0.028" datasheet: rev f 8 / 1 8 /1 4 - 6 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
t qp369182 dc- 6 ghz gain block package marking and dimensions marking: part number ? 369182 lot code ? aaxxxx n otes : 1. all dimensions are in millimeters. angles are in degrees . 2. dimension and tolerance formats conform to asme y14.4m - 1994. 3. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp- 012. 4. contact plating: nipdau pcb mounting pattern n otes : 1. all dimensions are in millimeters. angles are in d egrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. 4. do not remove or minimize via hole structure in the pcb. thermal and rf gr ounding is critical. 5. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10?). 6. ensure good package backside paddle solder attach for reliable operation and best electrical performance. 369182 a axxxx 1.62 (.064) 4.40 (.173) .35 (.014) .36 (.014) .44 (.017) 1.40 (.055) d1 d c b1 b symbol a 4.60 (.181) 4.50 (.177) 1.83 (.072) 1.73 (.068) 1.60 (.063) max .44 (.017) .48 (.019) .56 (.022) .50 (.020) .40 (.016) .42 (.0165) 1.50 (.059) typ min 3.94 (.155) 2.13 (.084) 2.29 (.090) e h l e1 e1 e symbol 2.29 (.090) 2.60 (.102) 4.25 (.167) 1.20 (.047) 1.50 bsc (.059) 1.10 (.043) 4.10 (.161) 3.00 bsc (.118) 2.20 (.087) 2.50 (.098) max min .89 (.035) typ 7 b e e1 2x b1 e l h d1 d c e1 d1 d1 alternate backside patterns - reflow compatible (part may be supplied with either pattern) a half etching depth 0.001" datasheet: rev f 8 / 1 8 /1 4 - 7 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
t qp369182 dc- 6 ghz gain block product compliance information esd sensitivity ratings caution! esd - sensitive device esd rating: class 1 c value: 1000 v and < 2 000 v test: human body model (hbm) standard: jedec standard jesd22 - a114 esd rating: class c3 v alue: 1000 v test: charged device model (cdm) standard: jedec standard jesd22 - c101 solderability compatible with both lead - free (260c maximum reflow temperature) and tin/lead (245c maximum reflow temperature) soldering processes. contact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating msl rating: level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 contact information for the latest specifications, additional product information, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@t riqui nt .com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@ triquint .com important notice the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability wh atsoever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly , to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical compone nts in medical, life - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. datasheet: rev f 8 / 1 8 /1 4 - 8 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
|
